400kV/500kV/20KV/1000kV/20000V/50kV High-Voltage Power Generator Step-up Boost

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
400kV/500kV/20KV/1000kV/20000V/50kV High-Voltage Power Generator Step-up Boost
Popular
Popular
Product Introduction
Description:
Voltage
Picture
Description
1000kV
Module type: MC-901
Input voltage: 3.7V-7.4V
Input current: 0.5A-1A
Input wire length: 9 cm
High voltage type: pulse DC type
Output voltage: 800KV-1000KV (please pay attention to safety when using)
Output current: 0.5A-1A
Output length: approximately16 cm
High voltage bipolar discharge distance: 1.5 cm -2 cm
Size:88x26mm(LxD)
Module use note:
1, high voltage module should avoid the use of high voltage no-load, power must be
adjusted before the high voltage line end of the right distance, high voltage wire drawing
distance and the use of battery voltage and capacity is proportional to.
2, the test arc distance from short to long experiment, when the power is prohibited
beyond the longest arc distance, due to the high pressure energy can not be released,
very easy to damage the module.
3, the power of the module, the internal heat is not heat, so not a long time to work.
Package Included:
1PC*High voltage inverter
400kV
input voltage: DC 3 V to 6 V
Input current: 2 A - 5 A
High pressure type: the type of pulse current
Output voltage: 400000 v(Please pay attention to safety)
High pressure discharge distance between: 10 mm - 20 mm
The output high voltage wire length: 100 mm
Input power cord length: 100 mm (the red line is positive)
Wiring:
Red and green power connection red line:"+" green line "-"
output : the other side ,same color cable
please notice:
the high-voltage module should avoid the use of electricity in high voltage no-load . (Power must be adjusted to a suitable distance to the high-voltage output line , battery capacity is proportional to the distance and the use of the high-pressure arc ( not a voltage as high as possible , you must provide enough current ) . Experimental test of the arc distance from short to long , Do not exceed the maximum arc distance electricity, energy can not be released due to high pressure , can easily damage the module. )
Work: intermittent , continuous work does not allow more than 1 minute and the output side does not allow shorting . Improper voltage and long working hours easily damaged module
Package Included:
1PC*DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator
500kV
Peripheral circuit is simple (just plug in switches, batteries can be) the discharge intensity violent.
Module Model: MCY-12-1
Physical volume: Length 70X 32mm diameter
Input voltage: 6V-12V
Input Current: 0.5A-1A
Input line length: 23 cm
High voltage type: DC type pulse
Output voltage: about 500KV (please pay attention to safety when used)
Output Current: 0.5A-1A
Output line length: about 92 cm
High voltage bipolar discharge distance: 2 cm -5 cm
Features:
This module is a science of small production with high voltage inverter transformer / booster finished module
After the input terminal DC6V-12V voltage can get tens of thousands of volts of direct current high voltage at the output,It can be used for high school science experiment, electronic equipment, negative ion generator, high voltage source when using scientific small production,Module uses the Tesla coil principle is made,
the output high voltage pulse current, small size, high efficiency
Precautions for use:
1, to avoid the use of electricity at high voltage load, must adjust the proper distance
between the front end of the high-voltage power-
2. to test the arc distance from short to long experiment, when power is strictly prohibited exceed
the maximum arcing distance, energy can not be released due to high pressure, easy to damage the module.
3, power module, the internal should not heat, so we can not work long hours.
4, determine whether the battery capacity can drive maximum power output of the battery
voltage measurement approach is arcing time. If 6V or so you can output the maximum power.
5, two small-capacity lithium series is 7.2V, measured in arc-state voltage has dropped to about 4V,
the capacity of the smaller voltage pull lower. It is proposed to use lithium 2000MA above,
the best conditions with more battery 4000MA.
Package Included:
1PC*DC12V DC pulse high-voltage module
20KV
Double high voltage cable can ignite cigarette and paper, a single high voltage cables can provide power to a metal body, and no sound support.
The module can be used as high-school scientific experiments, electronic devices, negative-ion generator, high-voltage source, to use when small science.
Over power:
Single 18650 or idle mobile phone batteries (the protective plate to remove the planned capacity of 2000mAh or more).
Note:
1. The high-voltage module should avoid the use of high-voltage current without a load. Power must be set to a suitable distance to the high voltage output line, the battery capacity is proportional to the distance and the use of the high pressure arc (not a voltage as high as possible, must provide sufficient current).
2. Experimental testing of the arc distance from short to long. If you do not exceed the maximum arc gap current, energy is not released by high pressure, the module can be easily damaged.
3. Due to the performance, the internal heat is not easy, each operating time should be set within 5 seconds.
Specification:
Material: metal, plastic
Color: black and black
Size: 19 x 20 x 18 mm (L x W x H)
Input voltage: DC3.6V-6V
Input Current: 1.5A
Output voltage: DC20KV (Please be sure to use safety when used)
Output current: 0.05A
InputLine Length: approx. 110 mm (red is positive)
Output cable length: approx. 110mm
High voltage bipolar discharge distance: 5mm
High type: pulse current
Structure: High and low voltage integrated
Package Included:
1PC*20 kV boost step-up power module
20000V
Input voltage: DC 12V
Output voltage: 15000V-20000V adjustable
Rated power: 5W
Mounting hole diameter: 5mm
Hole center distance: 112mm
Size: 60*70*30mm
Note: Small red and black line is input, red is 12V power supply positive input, black is negative input, thick red line is high voltage positive output, thick black line is high voltage negative output.
Package Included：
1PC*DC 12V to 20000V High-Voltage Electrostatic Generator Negative Ion Generator
50kV
1.Model:MC-105
2.Length:64mm
3.Diameter:24mm
4.Plane Diameter:21mm
5.Input Voltage:DC 3.7-6V
6.Input Current:2A-3A
7.Input Wire Length:10cm
8.High Voltage Form:pulse DC type
9.Output Voltage:50kV
10.Output Current:0.05A
11.Output Wire Length:8cm
12.High Voltage Polarization Discharging Distance:1-2cm
13.Using Method:red and green wire are input port;red wire is positive,green wire is negatice;other two high voltage wire are output port;fixing high voltage wire port for proper distance;and input port connects with battery can achieve high voltage arc
14.Input Power:can use single 3.7V lithium battery or 2S parallel connection,auch as 18650 battery etc
Package Included:
1PC*50kV High Voltage Pulse Generator Super Arc Pulse Ignition Coil Module
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.